Database with tested sensors/recievers
Moderator: Telldus
Re: Database with tested sensors/recievers
Updated wiki with sartano stock availability..
Re: Database with tested sensors/recievers
Hi
Good news !
Are you success with smoke detector ?
You think this Siren can work ?
http://www.ebay.co.uk/itm/Wireless-Exte ... 3a6d233c8d
regards
Good news !
Are you success with smoke detector ?
You think this Siren can work ?
http://www.ebay.co.uk/itm/Wireless-Exte ... 3a6d233c8d
regards
telldus Live!, http://tellmon.net, http://templight.se, Domospeak
tellstickNet rev17
20x otio,chacon,phoenix,GAO
2x THN132N
1x niclasf wireless t° sensor
tellstickNet rev17
20x otio,chacon,phoenix,GAO
2x THN132N
1x niclasf wireless t° sensor
Re: Database with tested sensors/recievers
i haven't received the smoke detector yet, so i dont knowlioelec wrote:Hi
Good news !
Are you success with smoke detector ?
You think this Siren can work ?
http://www.ebay.co.uk/itm/Wireless-Exte ... 3a6d233c8d
regards
No idea if it will work, a bit too expensive for me to try without knowing, sorry..
Re: Database with tested sensors/recievers
Hello
I use Wirelless energy meter on tellmon.net.
1)I note on my energy meter 1Wh/blink so I need to put 100 Watt-hours per blink to display correst value.
2)I note value seem to be don't correct on high value : Max counter 9Kw > display peek more 10kw.
https://picasaweb.google.com/lh/photo/W ... directlink
regards
I use Wirelless energy meter on tellmon.net.
1)I note on my energy meter 1Wh/blink so I need to put 100 Watt-hours per blink to display correst value.
2)I note value seem to be don't correct on high value : Max counter 9Kw > display peek more 10kw.
https://picasaweb.google.com/lh/photo/W ... directlink
regards
telldus Live!, http://tellmon.net, http://templight.se, Domospeak
tellstickNet rev17
20x otio,chacon,phoenix,GAO
2x THN132N
1x niclasf wireless t° sensor
tellstickNet rev17
20x otio,chacon,phoenix,GAO
2x THN132N
1x niclasf wireless t° sensor
Re: Database with tested sensors/recievers
sorry I'm not in good post reply, thanks niclasf for your supportlioelec wrote:Hello
I use Wirelless energy meter on tellmon.net.
1)I note on my energy meter 1Wh/blink so I need to put 100 Watt-hours per blink to display correst value.
2)I note value seem to be don't correct on high value : Max counter 9Kw > display peek more 10kw.
https://picasaweb.google.com/lh/photo/W ... directlink
regards
telldus Live!, http://tellmon.net, http://templight.se, Domospeak
tellstickNet rev17
20x otio,chacon,phoenix,GAO
2x THN132N
1x niclasf wireless t° sensor
tellstickNet rev17
20x otio,chacon,phoenix,GAO
2x THN132N
1x niclasf wireless t° sensor
Re: Database with tested sensors/recievers
Smoke alarm received today. It is not working out of the box, but with a very small mod it will work as a Waveman remote like the motion sensor and the magnetic switches listed on the Wiki page.
Head over to the wiki under noname brands and see what i found out and place to buy the smoke alarm
It was a long shipping, so be patient when you buy
http://tellstick-net.wikia.com/wiki/NON ... uff_etc..)
Head over to the wiki under noname brands and see what i found out and place to buy the smoke alarm
It was a long shipping, so be patient when you buy
http://tellstick-net.wikia.com/wiki/NON ... uff_etc..)
Re: Database with tested sensors/recievers
Hi, are about to buy the "Magnetic Door/Window sensors from Ebay - Tellstick Net (v4+v16)". Is it possible to remove the antenna and use wire? I want to try it out as a mailbox sensor and need to put the antenna outside the mailbox.
Does anyone else have better pictures from the board or can confirm that the antenna is removable.
Best Regards...
Does anyone else have better pictures from the board or can confirm that the antenna is removable.
Best Regards...
Re: Database with tested sensors/recievers
I am using one of them in my mailbox which is made of metal and a think brick wall between the sensor and my tellstick net, it is much more powerfull than the nexa magnetic switch.Minglarn wrote:Hi, are about to buy the "Magnetic Door/Window sensors from Ebay - Tellstick Net (v4+v16)". Is it possible to remove the antenna and use wire? I want to try it out as a mailbox sensor and need to put the antenna outside the mailbox.
Does anyone else have better pictures from the board or can confirm that the antenna is removable.
Best Regards...
I can try and take a few more pictures, but i wont remove the antenna myself, since its working for me already.
wait a few minutes and i will have the pictures uploaded
Looks like it's very easy to remove the antenna, but remember the wire have to have a specific lenght. as i remember 2,7 cm (2,7*5= 13,5cm or 2,7*10= 27 cm or 2,7*15=40,5 cm etc...)
Edit: I remembered wrong. found this in the swedish forum:
So its not 2.7 cm but 8.7, 17.3, 34.6 or 69.3 cm.sender på 433MHz, som er en bølgelengde på 69,3cm, og så lang skal antennen være. Eller dobbelt så stor osv, eller mindre 34,6cm, 17,3cm, 8,7cm
Last edited by simonbove on Sat Mar 29, 2014 1:15 pm, edited 1 time in total.
Re: Database with tested sensors/recievers
Perfect! So you use yours inside the mailbox too? I'll buy 4 of them and will try it my self.
The NEXA magnetic switches is no use inside a mailbox made of steel.
Thanks for the fast reply. At this moment I ordered 4 switches just in case something happens...
The NEXA magnetic switches is no use inside a mailbox made of steel.
Thanks for the fast reply. At this moment I ordered 4 switches just in case something happens...
Re: Database with tested sensors/recievers
Yw. Yes i do, started with nexa but only worked half the time,so i tried with these and its working perfectly for me, with metal box and thick brickwall.Minglarn wrote:Perfect! So you use yours inside the mailbox too? I'll buy 4 of them and will try it my self.
The NEXA magnetic switches is no use inside a mailbox made of steel.
Thanks for the fast reply. At this moment I ordered 4 switches just in case something happens...
remember they only turn off, so you need event which turns them back on.
Re: Database with tested sensors/recievers
Received my smoke detectors but they are not the same as mentioned in the wiki.
It still have the same pins as the old one showed in the wiki, however I cant make the Tellstick NET find it. As you can see I've soldered the pins so as they look like in the wiki but it just dont work. Any suggestions?
It seems that the seller has upgraded the smoke detectors with a new pcb board. See pictures.
It still have the same pins as the old one showed in the wiki, however I cant make the Tellstick NET find it. As you can see I've soldered the pins so as they look like in the wiki but it just dont work. Any suggestions?
It seems that the seller has upgraded the smoke detectors with a new pcb board. See pictures.
Re: Database with tested sensors/recievers
I recently received a PIR sensor from ebay which i could not get to work with tellstick net v4 or v16. It seems that the pcb does not allow changing jumpersettings. I attach a picture and a link to the seller so no one else does the same mistake.
http://www.ebay.co.uk/itm/433MHz-Pir-Se ... OU:US:3160
[attachment=-1]uploadfromtaptalk1397490736631.jpg[/attachment]
http://www.ebay.co.uk/itm/433MHz-Pir-Se ... OU:US:3160
[attachment=-1]uploadfromtaptalk1397490736631.jpg[/attachment]
- Attachments
-
- uploadfromtaptalk1397490736631.jpg (91.4 KiB) Viewed 15576 times
Re: Database with tested sensors/recievers
i think they sent you the wrong one. on the photos it should be with fixed coding and cant see that on your photo... complain to them
perhaps you can solder them..looks like it might work if they wont send new one...
perhaps you can solder them..looks like it might work if they wont send new one...
Re: Database with tested sensors/recievers
always try before soldering if its different design..Minglarn wrote:Received my smoke detectors but they are not the same as mentioned in the wiki.
It still have the same pins as the old one showed in the wiki, however I cant make the Tellstick NET find it. As you can see I've soldered the pins so as they look like in the wiki but it just dont work. Any suggestions?
It seems that the seller has upgraded the smoke detectors with a new pcb board. See pictures.
i think you have soldered the opposite side of the jumpersaka the wrong side.
is microcontroller called sc2262?
take some more photos ,difficult to see everything