My forum

Hello,
I try to install telldus-core on my readynas NV+ (with a sparc-padre processor) : http://www.readynas.com/?cat=4
The kernel is a 2.6.17, with some hacks from Netgear.
I plan to use my tellstick with domogik (http://www.domogik.org/). Domogik is already installed on my NAS.
I follow the How-to on your site : http://developer.telldus.com/wiki/TellS ... tionSource

What I've done :
- Compile and install a recent cmake
- Compile and install gcc 4.
- And compile and install telldus-core (2.1.0 and 2.0.104). The 2.0.4 doesn't compile on my nas.

I can launch the telldusd daemon, add the tellstick using tdadmin without errors.
But when I try to activate a light using tdtool, it says "No tellstick found".

What can I do ? Is there a way to activate debugging stuff in telldus-core or to increase verbosity ?

TIA

This thread seems to be related to mine : http://www.telldus.se/forum/viewtopic.p ... 5&start=30
But not really sure as I dont speak swedish

Is TellStick inserted before or after telldusd is started?
How do you call tdadmin?

The tellstick is inserted before starting the daemon

Here are some informations about my nas :

# lsusb
Bus 003 Device 008: ID 1781:0c31
...

According to this I've updated the modules options
# cat /etc/modprobe.d/tellstick
options ftdi_sio vendor=0x1781 product=0x0c31
udev is not installed on my nas

Here uis the long story

Insert the tellstick duo
# modprobe ftdi_sio

# cat /var/log/syslog
Oct 7 00:01:56 bibi-nas kernel: ::::::<6>usbcore: registered new driver usbserial
Oct 7 00:01:56 bibi-nas kernel: drivers/usb/serial/usb-serial.c: USB Serial Driver core
Oct 7 00:01:56 bibi-nas kernel: drivers/usb/serial/usb-serial.c: USB Serial support registered for FTDI USB Serial Device
Oct 7 00:01:56 bibi-nas kernel: ftdi_sio 3-1.2.1:1.0: FTDI USB Serial Device converter detected
Oct 7 00:01:56 bibi-nas kernel: drivers/usb/serial/ftdi_sio.c: Detected FT232BM
Oct 7 00:01:57 bibi-nas kernel: usb 3-1.2.1: FTDI USB Serial Device converter now attached to ttyUSB0
Oct 7 00:01:57 bibi-nas kernel: ftdi_sio 3-1.1:1.0: FTDI USB Serial Device converter detected
Oct 7 00:01:57 bibi-nas kernel: drivers/usb/serial/ftdi_sio.c: Detected FT232BM
Oct 7 00:01:57 bibi-nas kernel: usb 3-1.1: FTDI USB Serial Device converter now attached to ttyUSB1
Oct 7 00:01:57 bibi-nas kernel: usbcore: registered new driver ftdi_sio
Oct 7 00:01:57 bibi-nas kernel: drivers/usb/serial/ftdi_sio.c: v1.4.3:USB FTDI Serial Converters DriverO

# tdadmin controller connect --pid=0c31 --vid=1781 --serial=ttyUSB1
# /etc/init.d/telldusd start
Starting the Telldus TellStick daemon : telldusd.
tdtool --on 1
Turning on device 1, Example device - TellStick not found

# /etc/init.d/telldusd stop
Stopping the Telldus TellStick daemon: telldusd.

# tdadmin controller connect --pid=0c31 --vid=1781 --serial=ttyUSB0
# /etc/init.d/telldusd start
Starting the Telldus TellStick daemon : telldusd.
# tdtool --on 1
Turning on device 1, Example device - TellStick not found

ttyUSB1 appears to be my usb to parallel adaptater. I remove it and do the same process as above but that doesn't work.

This seems to be the problem:

bibi21000 wrote:# cat /etc/modprobe.d/tellstick
options ftdi_sio vendor=0x1781 product=0x0c31

bibi21000 wrote:Insert the tellstick duo
# modprobe ftdi_sio

This can block tellusd for accessing the device. Remove that.

After removing stuff in modprobe (tellstick duo don't use it), and removing kernel modules from memory.
I try :

# /etc/init.d/telldusd start
Starting the Telldus TellStick daemon : telldusd.

# tdadmin controller connect --pid=0c31 --vid=1781

# tdtool --on 1
Turning on device 1, Example device - TellStick not found

and that don't work

I will update the firmware of my nas soon, so I will get a fresh one.
Which release of the following program and library do you use :
gcc
libftdi
libconfuse

TIA

Up ...

A small note on this, when using tdadmin, don't forget to use hex and include serial: where <serialnum> can be found by running