relay output module

[lucbreton]

Hello everybody,
I've just bought a Tellstick net and I want to command a relay output module ( at least two independent dry contacts).
I didn't see such compatible device in the list of the main page of the web site.
Do you think that this device could work: http://www.velleman.eu/products/view/?id=375928 (Welleman 2-CHANNEL RF REMOTE CONTROL SET ; VM130)

Thanks in advance for your advices.

Luc

[lucbreton]

I answer myself to my post.
I got information from Velleman that they use a custom protocol.

Does somebody know a similar system (two relays with dry contacts) compatible with Tellstick?

Luc

[Jean-Julien]

hello

Les récepteurs pour volet roulant ont un contact sec

Receptors for roller shutters have a contact sec
http://www.domadoo.fr/produit,2800,1,CH ... -DI-O).htm

[lucbreton]

Bonjour Jean-Julien ( English translation below)
J’avais envisage cette possibilité mais dans la doc de ce module Chacon 54754 (http://www.chacon.be/media/sync/54751/F ... Manual.pdf ) il est spécifié dans utilisation « avec une lampe appuyer sur on ou off pour allumer la lampe ; celle-ci s’arrêtera automatiquement après 2 minutes » ( c’est également indiqué en hollandais, espagnol et portugais mais pas dans la version anglaise !!). Donc il y a une temporisation avant un retour à une position intermédiaire. Et ce n’est donc pas utilisable pour moi.
Pour les français seuls concernés par cette application : mon but est de recréer avec ces deux relais et deux diodes les signaux fil pilote pour un chauffage électrique.

I think there is a problem with the use of this Chacon module 54754 for dry contact applications. In the operation paragraph of the quick guide of the module (http://www.chacon.be/media/sync/54754/F ... 20907).pdf ) the French, Nederland, Spanish and Portuguese versions says “ With a lamp, push on ON or OFF to switch on the lamp; it will automatically switch off within 2 minutes” . But in the English part of this guide no information about this !!. If I believe to this information that means that this module creates an impulsion of 2 minutes and then stop and the contact return to a middle, non connected position (normal for roller shutter). But it is not usable as a simple relay with two stable positions ( NO and NC).

[Sykkeltom]

I need a NO (normally open) switch output for my heating thermostat in my cottage. When power from my Anslut receiver is on, then frost protection is activated. In case of mains power failure the cottage is heated when power returns, resulting in heating the cottage afterwards costing money. I have solved this problem by programming a Telldus Live schedule for each hour every day of the week, but this makes it more complicated to enable heating some hours before I arrive at my cottage.
I have carefully searched the on/off modules that are claimed to be compatible with Telldus Net for NO relay output without success.
I did find one, but it is not in the Telldus list of compatible devices. It is produced by LightwaveRF and is called JSJS LW821 and has a NO/NC relay output. Is this one compatible or hopefully can get compatible in the next version of the Telldus Live?
The JSJS LW821 is found here: http://www.lightwaverf.co.uk/LightwaveR ... LW821.html

[Jean-Charles71]

@lucbreton
bonjour
le module Chacon 54754 est bien un module temporisé qui revient à son état initial après 2 minutes.
De plus le relais est un inverseur et non deux contacts indépendants.
De quoi as tu besoin? 2 contacts secs indépendants?
Cordialement
Jean-Charles71

[Jean-Charles71]

@ Sykkeltom
Hi
Since you need a NO switch you can use Nexa LCLR-1000 or Intertechno ITL-1000.

The JSJS LW821 is a 2 minutes temporized product.

Best regards
Jean-Charles71

[simonbove]

or use this relayboard from ebay:

http://tellstick-net.wikia.com/wiki/NON ... ff_etc..)#