Page 1 of 2
433 mhz control relay board from China
Posted: Fri Mar 17, 2023 9:45 am
by OlavJohan
I have some of these relay boards bought at Ebay / Aliexpress. They come with a remote control with 2 or 4 buttons, and may have 1 to 4 relays. They are working OK together with the remote control, and I have also succeeded in controlling them from Tellstick. I have set the tellsticks to use the Sartano protocol and most of the time the selflearning procedyre of the boards accept the Sartano code.
But I would like to know if anyone of you know more about these boards used together with a Tellstick?
Take a look here:
http://www.ebay.com/itm/4-Channel-RF-Wi ... 33761e5e5a
Olav
Re: 433 mhz control relay board from China
Posted: Fri Mar 17, 2023 9:45 am
by lioelec
Hello
You have try this remote control and it work on telldus Live ?
How do settings code switch sartano with this remote control ?
Re: 433 mhz control relay board from China
Posted: Fri Mar 17, 2023 9:45 am
by OlavJohan
I have tried some settings like
12345ABCDEF
----------------
0111000001
0111000110
0111011111
0011000111
I have made a board with 1 relay work on up to 6 (or was it 8?) different code inclusive the remote control. I am not sure of the the pattern, but I think that the two rightmost settings has to do with the relays, so that 00, 01, 10, 11 for EF will trigger four different relays.
I have used the Sartano code switch option in Tellstick Net and also in Tellstick. But it is easier to program the relay board using Telldus Live / Tellstick Net. Press the learning button on the board, and then, very short after, the ON-button for the code in Telldus Live. I have struggled a bit, but have succeeded in making the relay(s) work. So far I have just tried the momentary settings as I am going to use a relay to restart some equipment.
Re: 433 mhz control relay board from China
Posted: Fri Mar 17, 2023 9:45 am
by lioelec
good news !
I will try it.
Re: 433 mhz control relay board from China
Posted: Fri Mar 17, 2023 9:45 am
by lioelec
Re: 433 mhz control relay board from China
Posted: Fri Mar 17, 2023 9:45 am
by Tommy88
Hi, I can confirm that the relay OlavJohan mentioned Works with telldus net with atleast one of the codes shown above.
However it lacked a proper manual so I used a little bit of time to figure it all out.
Here is a link to a "manual" I made for my own use.
If you don't understand Norwegian use Google translate^^
The 4dots with ring around 2 is how to use the different modes.
http://imageshack.us/photo/my-images/96/23an.png/?sa=0
Re: 433 mhz control relay board from China
Posted: Fri Mar 17, 2023 9:45 am
by TiE
Hi!
Is there anyone who has tried or had any Chinese relay board to work properly with TellStick?
I have a 8ch, and a 12ch board that I am trying to control with Tellstick.
The boards are mounted in DIY firingboxes to fire my 60mm - 130mm firework mortars.
The plan is to run Eventghost with the Timer, and Tellstick plugins.
Anyone with any clue
Kalle.
Re: 433 mhz control relay board from China
Posted: Fri Mar 17, 2023 9:45 am
by jejo72
Hi ,
I have tried with OlavJohan's code settings and i don't get it to work correctly.
He have used a 10 bit code pattern but what I can get out of the little information that i can find on the board is that it uses a 8 bit pattern.
I tried with the Roxcore Projector Screen with this settings:
1 11000011
- 00001100
0 00110000
and the relay board in toggle mode and then i can do an event and switch on and off 3 of the relay.
Is there any one that have tried and figure out what code pattern to use to be able to switch on and off all 4 relays?
Re: 433 mhz control relay board from China
Posted: Fri Mar 17, 2023 9:45 am
by tomm
Denne er helt genial som rele. Kan velge om du ønsker den skal bare slå inn i ett sekund eller veksle fast mellom NO C NC. Lagt inn i Telldus Live som CoCo self learning.
http://www.ebay.com/itm/1-Channel-433MH ... 4abedb0d30
Re: 433 mhz control relay board from China
Posted: Fri Mar 17, 2023 9:45 am
by Manticus2
and in english ?
parce que si moi aussi je me met à parler dans une langue que personne ne comprend c'est la fête ...
Re: 433 mhz control relay board from China
Posted: Fri Mar 17, 2023 9:45 am
by spinman49@gmail.com
Google translate est notre ami !!
"C'est absolument génial comme relais. Possibilité de choisir si vous voulez juste pour se transformer en un deuxième ou un commutateur coincé entre NO C NC. Publié dans Telldus Live comme CoCo auto-apprentissage."
Re: 433 mhz control relay board from China
Posted: Fri Mar 17, 2023 9:45 am
by simonbove
I have bought one from OP and with at normal tellstick i kan only control 3 of the relays, i have ordered a tellstick net now and will see if i can get it to accept all 4 relays..
If im succesfull then i will report back
Re: 433 mhz control relay board from China
Posted: Fri Mar 17, 2023 9:45 am
by arneolav
I got a releyboard like this (4 relays) :
http://www.ebay.com/itm/4-Channel-RF-Wi ... 33761e5e5a
I have defined it as RoxCore Projector screen and setup as described by jejo72:
1 11000011
- 00001100
0 00110000
Used the square as learning.
With TelldusNet/Live then I can then toggle on/off 2 of the four relays.
Re: 433 mhz control relay board from China
Posted: Fri Mar 17, 2023 9:45 am
by simonbove
arneolav wrote:I got a releyboard like this (4 relays) :
http://www.ebay.com/itm/4-Channel-RF-Wi ... 33761e5e5a
I have defined it as RoxCore Projector screen and setup as described by jejo72:
1 11000011
- 00001100
0 00110000
Used the square as learning.
With TelldusNet/Live then I can then toggle on/off 2 of the four relays.
i csn controll three relays with roxcore on and off. naybe yours is broken
Re: 433 mhz control relay board from China
Posted: Fri Mar 17, 2023 9:45 am
by arneolav
I can activate the relays by the up and down arrows.
on/off one relay by the arrow up, and the other by the arrow down.
How do you activate?