Receiver for wall sockets?

Moderator: Telldus

Post Reply
pekkak
Posts: 29
Joined: Fri Mar 17, 2023 9:45 am

Receiver for wall sockets?

Post by pekkak »

Is there a receiver that can be installed behind a fixed wall socket like in the picture?

Image

I don't want to use a plug-in receiver that can be tampered by e.g. kids.
reidar.ostrem
Posts: 45
Joined: Fri Mar 17, 2023 9:45 am

Re: Receiver for wall sockets?

Post by reidar.ostrem »

pekkak wrote:Is there a receiver that can be installed behind a fixed wall socket like in the picture?

Image

I don't want to use a plug-in receiver that can be tampered by e.g. kids.
+1 also looking for this
pekkak
Posts: 29
Joined: Fri Mar 17, 2023 9:45 am

Re: Receiver for wall sockets?

Post by pekkak »

I suppose Nexa LCMR-1000 is not possible to install behind a wall socket?
reidar.ostrem
Posts: 45
Joined: Fri Mar 17, 2023 9:45 am

Re: Receiver for wall sockets?

Post by reidar.ostrem »

pekkak wrote:I suppose Nexa LCMR-1000 is not possible to install behind a wall socket?
No it's not, and it does not seem to be any alternative to a plug in either :-(
Jean-Charles71
Posts: 19
Joined: Fri Mar 17, 2023 9:45 am
Location: France - Chalon sur Saône (71)
Contact:

Re: Receiver for wall sockets?

Post by Jean-Charles71 »

What is the depth of your box of embedding for the wall socket? In France it's 40 mm. So you need a deeper one.
Or a double box with a mask on the second part.
There is also a solution to use ONLY the output of NEXA LWMR-230 On/Off receiver or INTERTECHNO ITL-230.
They are special flat products.
Best regards
Jean-Charles71
pekkak
Posts: 29
Joined: Fri Mar 17, 2023 9:45 am

Re: Receiver for wall sockets?

Post by pekkak »

Good idea! Has anyone actually done it with LWMR-210?
Jean-Charles71
Posts: 19
Joined: Fri Mar 17, 2023 9:45 am
Location: France - Chalon sur Saône (71)
Contact:

Re: Receiver for wall sockets?

Post by Jean-Charles71 »

@ pekkak
Where are you from?
Your wall socket looks like french one.
pekkak
Posts: 29
Joined: Fri Mar 17, 2023 9:45 am

Re: Receiver for wall sockets?

Post by pekkak »

From Finland. I just didn't find better image quickly with Google. :)
Jean-Charles71
Posts: 19
Joined: Fri Mar 17, 2023 9:45 am
Location: France - Chalon sur Saône (71)
Contact:

Re: Receiver for wall sockets?

Post by Jean-Charles71 »

Pay attention, the LWMR-210 wich works only with light bulbs or halogen lamps.
Not with LEDs or energy-saving lamps.
Best regards
Jean-Charles71
pekkak
Posts: 29
Joined: Fri Mar 17, 2023 9:45 am

Re: Receiver for wall sockets?

Post by pekkak »

The problem with LWMR-210 is that max load is 230W. Before realizing that I just burned one LWMR-210 because I tried to use a vacuum-cleaner in the same wall socket. :oops:
etompau
Posts: 2405
Joined: Fri Mar 17, 2023 9:45 am
Location: Skåne

Re: Receiver for wall sockets?

Post by etompau »

Apart from the 230 W limitation of the LWMR-230, the unit also has a limitation on the type of load, it cannot handle inductive loads like a motor or an ordinary transformer. I managed to burn two units by connecting a toroid transformer to the unit ...
Jean-Charles71
Posts: 19
Joined: Fri Mar 17, 2023 9:45 am
Location: France - Chalon sur Saône (71)
Contact:

Re: Receiver for wall sockets?

Post by Jean-Charles71 »

If you can find some place in the wall behind the wall socket, you can install the Intertechno ITL-3500.
The max load is 3500 W.
3 appliances can be switched simultaneously or individualy (1500 W each) or 1 for 3500 W. It can be used for lamps, pump, heater, ventilators,...
But it's bigger than a 1000W receiver.
Regards.
Jean-Charles71
pekkak
Posts: 29
Joined: Fri Mar 17, 2023 9:45 am

Re: Receiver for wall sockets?

Post by pekkak »

Is this new Nexa product what I was looking for? :lol:

http://www.nexa.se/WMR-3500.htm
Post Reply