TelldusCenter 2.1.1 Beta

Moderator: Telldus

bjornta
Posts: 5
Joined: Fri Mar 17, 2023 9:45 am

Re: TelldusCenter 2.1.1 Beta

Post by bjornta »

mtm wrote:Hi.
I have updated to 2.1.1 beta and flashed my DUO. Works great and my ClasOhlsson thermometer have start working. But when the temperature gets below 0 the themperature doesnt wiew correctly. The temperature is just now -3.0 and the output is 33554428.9 When the temperature is over 0 it wiews corretly.
The thermometer is model 36-2953 and i bought a new sensor 36-1797 and both get the same result.
I have the same problem with UPM temperature and humidity sensors bought from Clas Ohlsson. Article numbers: 36-4040 (w/o humidity sensor) and 36-1794 (with humidity sensor).
As soon as they dip below zero degrees celsius they give weird values, as above.
micke.prag
Site Admin
Posts: 2243
Joined: Fri Mar 17, 2023 9:45 am
Location: Lund
Contact:

Re: TelldusCenter 2.1.1 Beta

Post by micke.prag »

Micke Prag
Software
Telldus Technologies
krambriw
Posts: 654
Joined: Fri Mar 17, 2023 9:45 am

Re: TelldusCenter 2.1.1 Beta

Post by krambriw »

In addition, those UPM/ESIC sensors do not work correctly if configured with HouseCode higher then 7.

HouseCode 1-7, DeviceCode 1-4 works ok but HouseCode 8 and higher gives strange readings.

Best regards, Walter
Mäg
Posts: 5
Joined: Fri Mar 17, 2023 9:45 am

Re: TelldusCenter 2.1.1 Beta

Post by Mäg »

I can confirm that downgrading the firmware brought my Oregon EA4C back in tellduscenter and switchking. Waiting for next firmware now :)
bjornta
Posts: 5
Joined: Fri Mar 17, 2023 9:45 am

Re: TelldusCenter 2.1.1 Beta

Post by bjornta »

Mäg wrote:I can confirm that downgrading the firmware brought my Oregon EA4C back in tellduscenter and switchking. Waiting for next firmware now :)
Do you see the UPM temperature/humidity sensors as well?
Mäg
Posts: 5
Joined: Fri Mar 17, 2023 9:45 am

Re: TelldusCenter 2.1.1 Beta

Post by Mäg »

bjornta wrote: Do you see the UPM temperature/humidity sensors as well?
I don't own one of those.
krambriw
Posts: 654
Joined: Fri Mar 17, 2023 9:45 am

Re: TelldusCenter 2.1.1 Beta

Post by krambriw »

Jag är lite osäker på huruvida mina Oregon sensorer skall stödjas eller ej i denna beta och om jag skall göra något speciellt för att få in dom. Jag ser i alla fall inget som trillar in som liknar värdena som semnsorerna visar på sina displayer

Enligt release noten: + Support for Oregon 0x1A2D (#144)

Mina sensorer hittas av min RFXCOM och två av dom identifieras då så här:

Code: Select all

501A2D4007600790063762   TH1[1796] THGN122N,THGR122NX,THGR228N,THGR268 CH 3 addr:07 temp:7,6C | 45,68F hum:69 Normal  bits=80 
501A2D2020300250C93345   TH1[8194] THGN122N,THGR122NX,THGR228N,THGR268 CH 2 addr:20 temp:2,3C | 36,14F hum:95 Wet     bits=80
1A2D finns ju med i dessa id'n

Jag har dessa (THGR238N): http://www.prisjakt.nu/produkt.php?p=567954

mvh Walter
rob
Posts: 1
Joined: Fri Mar 17, 2023 9:45 am
Location: Stockholm

Re: TelldusCenter 2.1.1 Beta

Post by rob »

micke.prag wrote:Wow, Marten0615. What an error report. What if everybody was as thorough as you!
I just remember that you probably have a too early firmware without support for the automatic upgrading using the utility. Please send me an email and I will explain how you can upgrade the firmware manually. You need the ip-address of your device.
Hi Micke

I have the same problem that Marten0615 has, can you please help me to?
LoA
Posts: 24
Joined: Fri Mar 17, 2023 9:45 am

Re: TelldusCenter 2.1.1 Beta

Post by LoA »

Since upgrading to the beta I find one new sensor (Mandolyn WT450H, branded ESIC) wich gives me both temp and RF, nice :-)

As the rest of the users of the erlier supportet CO-sensor (labeled RAR081) I´m now lacking support, not nice :-(

I have three Oregon THGN132N wich I was hoping would start work In the next FW (as it´s been said earlier that Oregon-sensors would be a priority and they are well documented). Really not nice :-(

Telldus, are the THGN132N supposed to be a part of the new FW but suffering from the same bug that the CO-sensor seems to have??
Post Reply