I haven't been around for a long time... I'm trying to get back to the software I've been writing for Tellstick and MediaPortal but now but I have a problem with my receiver -
The Nexa PB-3
https://www.m.nu/fjarrstrombrytare-3x10 ... 411a9bce94
Usually when I plug this units in there's a light that blinks for a few seconds while it's in learning mode. However when I plug this unit in the light just turns on and doesn't blink (and nor Tellstick nor the Nexa remote control) cannot teach it a new command.
Is there anyone who might have an idea what's wrong or does that seem like a technical problem with the unit itself?
What do you think?
Problem with Nexa PB-3
Moderator: Telldus
Problem with Nexa PB-3
Software and hardware solutions for the home theater PC (HTPC) at HTPCSolutions.com
-
- Posts: 61
- Joined: Fri Mar 17, 2023 9:45 am
Re: Problem with Nexa PB-3
Memory full?
TO CHANGE OR DELETE CODE :
INDIVIDUAL DELETE -
* Pull out the receiver from wall outlet (Fig. 5) and after 5 seconds plug the receiver into wall outlet again (Fig. 6).
* Receiver LED indicator blinks slowly for 5 seconds (Fig. 7).
* Within the receiver LED indicator blinking 5 seconds, bringing the transmitter near the receiver, pressing the “OFF” button of the specific channel (channel 1, 2, 3) (Fig. .
* Receiver LED stops blinking, lamp blinks twice to confirm the code is deleted.
ALL MEMORY DELETE-
* Pull out the receiver from wall outlet (Fig. 9) and after 5 seconds plug the receiver into wall outlet again (Fig. 10).
* Receiver LED indicator blinks slowly for 5 seconds (Fig. 11).
* Within the receiver LED indicator blinking 5 seconds, bringing the transmitter near the receiver, pressing the “GROUP OFF” button (Fig. 12).
* Receiver LED stops blinking, lamp blinks twice to confirm all the memorised codes (3 sets) are deleted from the receiver.
TO CHANGE OR DELETE CODE :
INDIVIDUAL DELETE -
* Pull out the receiver from wall outlet (Fig. 5) and after 5 seconds plug the receiver into wall outlet again (Fig. 6).
* Receiver LED indicator blinks slowly for 5 seconds (Fig. 7).
* Within the receiver LED indicator blinking 5 seconds, bringing the transmitter near the receiver, pressing the “OFF” button of the specific channel (channel 1, 2, 3) (Fig. .
* Receiver LED stops blinking, lamp blinks twice to confirm the code is deleted.
ALL MEMORY DELETE-
* Pull out the receiver from wall outlet (Fig. 9) and after 5 seconds plug the receiver into wall outlet again (Fig. 10).
* Receiver LED indicator blinks slowly for 5 seconds (Fig. 11).
* Within the receiver LED indicator blinking 5 seconds, bringing the transmitter near the receiver, pressing the “GROUP OFF” button (Fig. 12).
* Receiver LED stops blinking, lamp blinks twice to confirm all the memorised codes (3 sets) are deleted from the receiver.
Driver http://kameran.nu - Mitt foto galleri.
Kom gärna förbi och kolla mina bilder...
Kom gärna förbi och kolla mina bilder...
Re: Problem with Nexa PB-3
Like I said, no blinking at all.
Software and hardware solutions for the home theater PC (HTPC) at HTPCSolutions.com
-
- Site Admin
- Posts: 2243
- Joined: Fri Mar 17, 2023 9:45 am
- Location: Lund
- Contact:
Re: Problem with Nexa PB-3
Is it possible to control the receiver from one of the remotes that was learned from previous attempts?
Micke Prag
Software
Telldus Technologies
Software
Telldus Technologies
Re: Problem with Nexa PB-3
No, unfortunately not...micke.prag wrote:Is it possible to control the receiver from one of the remotes that was learned from previous attempts?
Software and hardware solutions for the home theater PC (HTPC) at HTPCSolutions.com
-
- Site Admin
- Posts: 2243
- Joined: Fri Mar 17, 2023 9:45 am
- Location: Lund
- Contact:
Re: Problem with Nexa PB-3
Do you only have one receiver or does all of them behave this strange?
Micke Prag
Software
Telldus Technologies
Software
Telldus Technologies
Re: Problem with Nexa PB-3
Only one of them behaves this way.
I didn't have many units to begin with, I want to get back to developing the mediaportal plugin but I need working receivers for that.
I really need to order me a shipment of receivers from my favorite Swedish store... Too bad shipping is so expensive...
So the PB-3 is dead? No secret button somewhere that restarts it or something?
I didn't have many units to begin with, I want to get back to developing the mediaportal plugin but I need working receivers for that.
I really need to order me a shipment of receivers from my favorite Swedish store... Too bad shipping is so expensive...
So the PB-3 is dead? No secret button somewhere that restarts it or something?
Software and hardware solutions for the home theater PC (HTPC) at HTPCSolutions.com