Simple light bulb socket receiver
Moderator: Telldus
Simple light bulb socket receiver
Hello,
I have a simple receiver that is connected directly between the light bulb and the socket, it looks something like this:
http://www.kjell.com/?item=50354&path=3 ... ,331000000
On the remote that comes with it, it says: 433.92Mhz
Is there a way for me to control it with my Tellstick?
I have a simple receiver that is connected directly between the light bulb and the socket, it looks something like this:
http://www.kjell.com/?item=50354&path=3 ... ,331000000
On the remote that comes with it, it says: 433.92Mhz
Is there a way for me to control it with my Tellstick?
-
- Site Admin
- Posts: 2243
- Joined: Fri Mar 17, 2023 9:45 am
- Location: Lund
- Contact:
Does it look "something" like that or is it that one?
We support many different types of receivers, if you cannot tell us the brand of yours it is hard for us to tell you if we support it.
If yours i Nexa/Proove as the link you supplied it can be setup in TelldusCenter as this guide shows:
http://developer.telldus.se/wiki/Usage% ... e%20system
We support many different types of receivers, if you cannot tell us the brand of yours it is hard for us to tell you if we support it.
If yours i Nexa/Proove as the link you supplied it can be setup in TelldusCenter as this guide shows:
http://developer.telldus.se/wiki/Usage% ... e%20system
Micke Prag
Software
Telldus Technologies
Software
Telldus Technologies
So here's the thing, it's not exactly it, but it looks like it, I thought all those units are basically the same - manufactured in the same factory in china or something... .
So my real question is this - if a unit is not self-learning, and I have a unit and it's remote control, is there a way for me to make TellStick learn the code? Can it work like this?
I also have a few Nexa units coming in the mail tomorrow, I'm sure it'll be much simpler with those...
So my real question is this - if a unit is not self-learning, and I have a unit and it's remote control, is there a way for me to make TellStick learn the code? Can it work like this?
I also have a few Nexa units coming in the mail tomorrow, I'm sure it'll be much simpler with those...
micke.prag wrote:Does it look "something" like that or is it that one?
We support many different types of receivers, if you cannot tell us the brand of yours it is hard for us to tell you if we support it.
If yours i Nexa/Proove as the link you supplied it can be setup in TelldusCenter as this guide shows:
http://developer.telldus.se/wiki/Usage% ... e%20system
-
- Site Admin
- Posts: 2243
- Joined: Fri Mar 17, 2023 9:45 am
- Location: Lund
- Contact:
A lot of receivers comes from the same manufacturer in China. But without knowing which one you have we cannot tell you if it works or not. Please supply the brand name, where you bought it or something!
Even if you know the unitcode you cannot use it without knowing which protocol (manufacturer) it uses.
Even if you know the unitcode you cannot use it without knowing which protocol (manufacturer) it uses.
Micke Prag
Software
Telldus Technologies
Software
Telldus Technologies
I'll just wait for the Nexa units then... I thought it would also work with no-name units as well... (somehow learn the code through the remote, like universal remote works). Never mind... thank you anyhow!micke.prag wrote:A lot of receivers comes from the same manufacturer in China. But without knowing which one you have we cannot tell you if it works or not. Please supply the brand name, where you bought it or something!
Even if you know the unitcode you cannot use it without knowing which protocol (manufacturer) it uses.
Re: Simple light bulb socket receiver
Lamp hållaren som länkades, fungerar den?moryoav wrote:Hello,
I have a simple receiver that is connected directly between the light bulb and the socket, it looks something like this:
http://www.kjell.com/?item=50354&path=3 ... ,331000000
On the remote that comes with it, it says: 433.92Mhz
Is there a way for me to control it with my Tellstick?
-
- Site Admin
- Posts: 2243
- Joined: Fri Mar 17, 2023 9:45 am
- Location: Lund
- Contact:
Bought one of these from Kjell&CO (#50354), added this code to tellstick.conf
it doesn't selflearn like my other PROOVE selflearning switches do.
Any help or thoughts would be appreciated.
Code: Select all
device {
id = 23
name = "PROOVE socket"
protocol = "arctech"
model = "selflearning-switch"
parameters {
house = "112233"
unit = "3"
}
}
Any help or thoughts would be appreciated.
-
- Site Admin
- Posts: 2243
- Joined: Fri Mar 17, 2023 9:45 am
- Location: Lund
- Contact:
This receiver is a PROOVE LBUR-100 Batch 10246, bought it today just to test it. It blinks the red LED for 5 secs after pushing the button, otherwise nothing happens.
Other PROOVE devices like LYCR-3500 and LYCR-300 learns just fine with tdtool.
Tried different distances from wrapping the tellstick wire antenna round the receiver up to several meters.
Other PROOVE devices like LYCR-3500 and LYCR-300 learns just fine with tdtool.
Tried different distances from wrapping the tellstick wire antenna round the receiver up to several meters.