Updated (too large) image available
Posted: Fri Mar 17, 2023 9:45 am
Hi,
Edit: Torrent removed, better use this post instead: http://www.telldus.com/forum/viewtopic.php?f=25&t=4243
I have created a new image where I have updated as much as I could/knew.
Unfortunately I only had a 16Gb SD card available, so the image is way too big for regular use.
Sorry for the inconvenience. Feel free to replicate the below and publish a smaller image.
Updated the OS
Updated Automagically
Raspi-config
- Updated Timezone (Europe/Stockholm)
Removed stuff from the configuration
- Removed all /core/ items
- Removed all /signals/ items
- Cleansed /etc/tellstick.conf
Prepared for Xively plugin
Added some extas
~/source/smhi_parse.py
As decribed in this post: http://www.telldus.com/forum/viewtopic.php?f=25&t=4135
~/source/xively.py
As described in this post: http://www.telldus.com/forum/viewtopic.php?f=25&t=4220
To enable this plugin, do the following:
Remember to remove the file before the next update if David decides to merge the pull request.
Added a test device and accompanying remote
- A single Raw Tellstick Device called Test is available
- A single Remote named Main with a page Home having a single On/Off called Test
To use the above test-device, enter /admin/core/rawtellstickdevice/ and update the details of the Test device to match your device.
That is, change House and Unit code to match a device in your home.
Found here: Attached as torrent (to large for anything else)
MD5 of img file inside the zip: c15a73b95b98e2ca51a8a74b0d327511
Based on sourcecode revision: c9821d8
Source repository and issue tracker: https://bitbucket.org/davka003/automagically/
UserID for console/ssh/admin interface: pi
UserID for mysql: root
Password for the above: raspberry (I advice you to change this but I haven't yet put any instructions on all the places needed to be changed)
Follow the instructions here:
http://automagically.weebly.com/home-automation.html
Ironically, you might want to make use of the full partition of your SD card. Run raspi-config and Expand Filesystem
Once again, sorry for the large size of the image.
/Marcus
Edit: Torrent removed, better use this post instead: http://www.telldus.com/forum/viewtopic.php?f=25&t=4243
I have created a new image where I have updated as much as I could/knew.
Unfortunately I only had a 16Gb SD card available, so the image is way too big for regular use.
Sorry for the inconvenience. Feel free to replicate the below and publish a smaller image.
Updated the OS
Code: Select all
$ sudo apt-get update
$ sudo apt-get upgrade
$ sudo apt-get dist-upgrade
$ sudo apt-get clean
$ sudo apt-get autoclean
Code: Select all
$ cd source/automagically/
$ sudo ./update.sh
- Updated Timezone (Europe/Stockholm)
Removed stuff from the configuration
- Removed all /core/ items
- Removed all /signals/ items
- Cleansed /etc/tellstick.conf
Prepared for Xively plugin
Code: Select all
$ sudo pip install requests
~/source/smhi_parse.py
As decribed in this post: http://www.telldus.com/forum/viewtopic.php?f=25&t=4135
~/source/xively.py
As described in this post: http://www.telldus.com/forum/viewtopic.php?f=25&t=4220
To enable this plugin, do the following:
Code: Select all
$ sudo sudo /etc/init.d/automagically stop
$ cp ~/source/xively.py ~/source/automagically/site/plugins/.
$ sudo sudo /etc/init.d/automagically start
Code: Select all
$ sudo sudo /etc/init.d/automagically stop
$ sudo rm ~/source/automagically/site/plugins/xively.py*
$ sudo sudo /etc/init.d/automagically start
- A single Raw Tellstick Device called Test is available
- A single Remote named Main with a page Home having a single On/Off called Test
To use the above test-device, enter /admin/core/rawtellstickdevice/ and update the details of the Test device to match your device.
That is, change House and Unit code to match a device in your home.
Found here: Attached as torrent (to large for anything else)
MD5 of img file inside the zip: c15a73b95b98e2ca51a8a74b0d327511
Based on sourcecode revision: c9821d8
Source repository and issue tracker: https://bitbucket.org/davka003/automagically/
UserID for console/ssh/admin interface: pi
UserID for mysql: root
Password for the above: raspberry (I advice you to change this but I haven't yet put any instructions on all the places needed to be changed)
Follow the instructions here:
http://automagically.weebly.com/home-automation.html
Ironically, you might want to make use of the full partition of your SD card. Run raspi-config and Expand Filesystem
Code: Select all
$ sudo raspi-config
/Marcus