Problem with Nexa PB-3

Moderator: Telldus

Post Reply
moryoav
Posts: 33
Joined: Thu Jan 18, 2018 11:08 am

Problem with Nexa PB-3

Post by moryoav » Thu Jan 18, 2018 11:08 am

I haven't been around for a long time... I'm trying to get back to the software I've been writing for Tellstick and MediaPortal but now but I have a problem with my receiver -
The Nexa PB-3

https://www.m.nu/fjarrstrombrytare-3x10 ... 411a9bce94

Usually when I plug this units in there's a light that blinks for a few seconds while it's in learning mode. However when I plug this unit in the light just turns on and doesn't blink (and nor Tellstick nor the Nexa remote control) cannot teach it a new command.

Is there anyone who might have an idea what's wrong or does that seem like a technical problem with the unit itself?

What do you think?
Software and hardware solutions for the home theater PC (HTPC) at HTPCSolutions.com

KungenAvPeking
Posts: 61
Joined: Thu Jan 18, 2018 11:08 am

Re: Problem with Nexa PB-3

Post by KungenAvPeking » Thu Jan 18, 2018 11:08 am

Memory full?

TO CHANGE OR DELETE CODE :
INDIVIDUAL DELETE -
* Pull out the receiver from wall outlet (Fig. 5) and after 5 seconds plug the receiver into wall outlet again (Fig. 6).
* Receiver LED indicator blinks slowly for 5 seconds (Fig. 7).
* Within the receiver LED indicator blinking 5 seconds, bringing the transmitter near the receiver, pressing the “OFF” button of the specific channel (channel 1, 2, 3) (Fig. 8).
* Receiver LED stops blinking, lamp blinks twice to confirm the code is deleted.

ALL MEMORY DELETE-
* Pull out the receiver from wall outlet (Fig. 9) and after 5 seconds plug the receiver into wall outlet again (Fig. 10).
* Receiver LED indicator blinks slowly for 5 seconds (Fig. 11).
* Within the receiver LED indicator blinking 5 seconds, bringing the transmitter near the receiver, pressing the “GROUP OFF” button (Fig. 12).
* Receiver LED stops blinking, lamp blinks twice to confirm all the memorised codes (3 sets) are deleted from the receiver.
Driver http://kameran.nu - Mitt foto galleri.
Kom gärna förbi och kolla mina bilder... ;)

moryoav
Posts: 33
Joined: Thu Jan 18, 2018 11:08 am

Re: Problem with Nexa PB-3

Post by moryoav » Thu Jan 18, 2018 11:08 am

Like I said, no blinking at all.
Software and hardware solutions for the home theater PC (HTPC) at HTPCSolutions.com

micke.prag
Site Admin
Posts: 2242
Joined: Thu Jan 18, 2018 11:08 am
Location: Lund
Contact:

Re: Problem with Nexa PB-3

Post by micke.prag » Thu Jan 18, 2018 11:08 am

Is it possible to control the receiver from one of the remotes that was learned from previous attempts?
Micke Prag
Software
Telldus Technologies

moryoav
Posts: 33
Joined: Thu Jan 18, 2018 11:08 am

Re: Problem with Nexa PB-3

Post by moryoav » Thu Jan 18, 2018 11:08 am

micke.prag wrote:Is it possible to control the receiver from one of the remotes that was learned from previous attempts?
No, unfortunately not...
Software and hardware solutions for the home theater PC (HTPC) at HTPCSolutions.com

micke.prag
Site Admin
Posts: 2242
Joined: Thu Jan 18, 2018 11:08 am
Location: Lund
Contact:

Re: Problem with Nexa PB-3

Post by micke.prag » Thu Jan 18, 2018 11:08 am

Do you only have one receiver or does all of them behave this strange?
Micke Prag
Software
Telldus Technologies

moryoav
Posts: 33
Joined: Thu Jan 18, 2018 11:08 am

Re: Problem with Nexa PB-3

Post by moryoav » Thu Jan 18, 2018 11:08 am

Only one of them behaves this way.
I didn't have many units to begin with, I want to get back to developing the mediaportal plugin but I need working receivers for that.

I really need to order me a shipment of receivers from my favorite Swedish store... Too bad shipping is so expensive...

So the PB-3 is dead? No secret button somewhere that restarts it or something?
Software and hardware solutions for the home theater PC (HTPC) at HTPCSolutions.com

Post Reply