My forum

axiom wrote: btw is Automagically OpenSource?

https://bitbucket.org/davka003/automagically
/Marcus
ps. Have no clue about your other question...

Strange, that sounds like something that's an error with the image you use (and I made according to previous posts). Did you set your longitude, latitude and timezone properly in Automagically? I guess so cause if you used my reference image it should have long/lat at the castle in Stockholm if I re...

Strange, that sounds like something that's an error with the image you use (and I made according to previous posts). Yes, I had made a mistake. A new image has been made available, but you can also fix this by logging in to the pi and do the following: $ sudo service automagically stop $ sudo servi...

Hi, A new image for a 4Gb SD card has been created based on the latest version of Automagically (2014-03-07). Found here : Attached as torrent Found here too : https://www.dropbox.com/s/iew29kepqazqz98/automagically_2014_03_07.zip MD5 of img file inside the zip : 7a01756348469a45d4646650553291e0 Siz...

Hi, I noticed that Xively has some issues when sending data to frequently, typically the first message is lost for some reason. So if you want to upload both E and Pmom to Xively you might want to send it in the message to Xively. Use this signal transform to do so: Pattern to match: wem,data;status...

Hi,

Have not tested, but if email sender is configured and you can 'see' the event in the signal trace, then it's all hunkeydorey. A transform resulting in a signal as below format should do the trick:
email:toaddress:subject:message text

Marcus

Hi, Bought an Edimax and had severe issues with it using the Pi's USB port. Sometimes the Pi got unresponsive but more often the signal handler of Automagically died. Moved it to the externally powered USB hub and now it all works fine. Just as good as when it was on Ethernet cable. Seems the Edimax...

Hi, Bought an Edimax and had severe issues with it using the Pi's USB port. Sometimes the Pi got unresponsive but more often the signal handler of Automagically died. Moved it to the externally powered USB hub and now it all works fine. Just as good as when it was on Ethernet cable. Seems the Edima...

Looks like normal behaviour of Nexa/Proove remotes that seems to build-in multiple protocols. I would first use a Find repeats in signal admin and feed that to a Transform in order to only get one mail. Of you transform directly you will get 2-3 mails each time someone rings your bell. I would have ...

Another thing, I will say a little strange behavior, is about my powered USB-hub. If I make a restart or a reboot of the Pi, will the red LED on the Pi remain as it was powered up. This fact will make that the Pi will not start up after restart/reboot. I must disconnect the USB Cable before it will...

Two posts comes to mind,

If-then-else kind of,
http://www.telldus.com/forum/viewtopic.php?f=25&t=4260

Calculations,
http://www.telldus.com/forum/viewtopic.php?f=25&t=4261

Can partly be done in signal transforms using $EVAL.

Feel free to update the wiki...

Marcus

Version 0.7 has been committed to bitbucket and a pull request has been created for David to assess. This version adds a protocol wrap that occurs when the energy meter has detected more that 2048 blinks and wraps to negative numbers on the protocol. It can be downloaded using this command: $ wget h...

Which files have you updated? Thanks in advance for correct lines in the needed files!!! For some reason, my device created two entires in the 70-persistent-net.rules and the wlan adapter ended up on wlan1. To see if that has happened, enter the following: $ iwconfig Here are my files: /etc/network...

Version 0.8 has been committed to bitbucket and a pull request has been created for David to assess. This version implements special case to handle -0.0 from energy meter. It can be downloaded using this command: $ wget https://bitbucket.org/MarcusKarlsson/automagically/raw/7a8e04048203cf92059ce59ef...

misterleffe wrote: Do I have to restart the Pi before settings will work?

If you just replace ssid and psk from my files with your own, I think you can use them as-is.
You need to restart the device, easiest way is to reboot.

(For AES, CCMP will be used)

/Marcus